Boiler Repair
When the boiler quits on a January night, the radiators go cold fast and the pipes are next. We repair steam and hot-water boilers, from the burner to the last radiator.
Learn moreWater heaters
Your house already has a hot-water boiler, but domestic hot water comes from a tankless coil that runs lukewarm or a separate heater burning fuel on its own. An indirect tank uses the boiler you already have, more effectively.

An indirect water heater is an insulated storage tank with a coil inside, heated by water from your boiler instead of its own burner. Typical Hartford-area installs run about $2,465 to $4,685, including piping and controls. We answer 24/7, check that your boiler suits the setup, and usually schedule the install within a week or two.
Many older oil and gas boilers have a tankless coil: a copper coil inside the boiler that heats water as it flows through. To make hot water on demand, the boiler has to stay hot all year, including summer, which wastes fuel. Coils also scale up and lose capacity, so hot water fades during long showers.
An indirect tank stores hot water in an insulated tank. Boiler water flows through a coil inside the tank only when it calls for heat, then the boiler can shut off. The stored water handles peaks like back-to-back showers well, and the boiler does not have to idle hot in summer. For many homes with a sound boiler, it is a strong upgrade.
The indirect tank connects to the boiler as its own zone, either with a dedicated circulator or a zone valve. We usually set it up as a priority zone, so when the tank calls for heat, it gets the boiler's full output briefly before space heating resumes. On modern boilers, the control often has a built-in indirect sensor input.
On the domestic side, the tank gets a cold supply with a shut-off, a temperature and pressure relief valve, and a thermostatic mixing valve. The mixing valve lets the tank store water hotter, which helps capacity and controls bacteria growth, while sending safe-temperature water to fixtures. We add an expansion tank on the domestic side if the system is closed.
An indirect tank is only as good as the boiler feeding it. We check the boiler's age, condition and output, plus the piping and controls. A boiler near the end of its life may be better replaced at the same time, and a modern modulating boiler can work well with an indirect if piped correctly.
Steam boilers are a different case. Indirect tanks can be connected to some steam boilers below the waterline, but it takes careful piping, and it is not always practical. For many steam houses, a separate gas, electric or heat pump water heater makes more sense. We tell you which approach fits your heating system after looking at it.

Hartford and its older suburbs have a lot of houses heated by hot-water boilers, many with tankless coils that have scaled up over the years. Two- and three-family buildings often have one boiler per unit or a single boiler serving several apartments, which changes how we size an indirect tank. In Manchester, Wethersfield and West Hartford, swapping a coil for an indirect is a common upgrade. Check current Energize CT offers when replacing heating or hot water equipment.
Tank size, boiler type and controls, piping distance and any boiler repairs needed change the price most. Typical Hartford-area range, confirmed on site before work starts. Compare all prices.
Process
We look at the boiler's type, condition, output and controls to confirm it can run an indirect tank.
We choose a tank size for your hot water use and plan the zone piping, valves and control wiring.
We set the tank, pipe the boiler zone and domestic side, add a mixing valve and wire the controls.
We fill, purge air, test the zone and relief valve, set temperatures and show you how it works.
FAQ
Yes. Indirect tanks work with oil, gas and propane hot-water boilers. Swapping a tankless coil for an indirect tank on an oil boiler often lets the boiler shut down between calls in summer instead of staying hot all day, which can save fuel. We check that the boiler is sound first.
Most installs take one day, including setting the tank, piping the boiler zone and domestic side, and testing. If we need to add a circulator, upgrade controls or repair boiler piping, it may take longer. Hot water and heat may be off for part of the day.
Many homes do well with a 40 to 50 gallon indirect tank, while larger households or homes with big tubs may need more. Boiler output also matters, because a larger boiler recovers the tank faster. We size by your fixtures, family and boiler, not just the tank label.
Related work
When the boiler quits on a January night, the radiators go cold fast and the pipes are next. We repair steam and hot-water boilers, from the burner to the last radiator.
Learn moreWhen an old boiler is cracked, rusted through or costing a fortune in repairs, a new one sized right for the house can heat better and burn less fuel. Sizing...
Learn moreThe tank is leaking from the bottom, or it is old enough that every repair is money down the drain. A replacement done right means the right size, safe venting...
Learn moreA plumber answers, day or night, and gives you a price before any work starts.