Skip to content
Plumbing VernonHartford, CT plumbersAnswered 24/7(860) 926-8723

Kitchen & bath

New toilet installation for Hartford bathrooms

The old toilet is cracked, uses too much water, or just will not stop causing trouble. A new toilet is a simple upgrade when it is set level, sealed right and connected with new parts.

  • Answered 24/7
  • Price before work
  • Hartford + nearby towns
new elongated white toilet being set onto a fresh wax ring over a closet flange on a tiled bathroom floor
Typical range $285 to $865(860) 926-8723Price confirmed on site before work starts
Quick answer

Toilet installation removes the old toilet and sets a new one with a fresh wax or foam seal, new closet bolts and a new supply line, checking the flange and floor. Typical Hartford-area installs run about $285 to $565 for labor and parts, plus the toilet. We answer 24/7, and most installs are done the same day.

Signs you need toilet installation

  • The bowl or tank is cracked, or the porcelain is badly stained
  • The toilet clogs often even after the drain has been cleaned
  • An older toilet uses far more water per flush than newer models
  • You are updating the bathroom and want a comfort-height or elongated bowl
  • Repairs keep adding up on a toilet with hard-to-find parts

Picking a toilet that fits

The most important measurement is the rough-in, the distance from the finished wall to the center of the closet bolts. Most toilets are made for a twelve-inch rough-in, but older homes sometimes have ten- or fourteen-inch rough-ins. Buying the wrong size leaves the tank too close to or too far from the wall. We measure before you buy.

Elongated bowls are more comfortable but take more room than round bowls, which matters in small older bathrooms. Comfort-height toilets sit higher and can be easier to use. WaterSense-labeled toilets meet efficiency and performance criteria. Two-piece toilets are common and easier to carry up narrow stairs, while one-piece models are easier to clean around the base.

Flange, floor and seal

When the old toilet comes off, we inspect the closet flange. Older homes may have cast-iron or lead bends with brass or iron flanges that are cracked or corroded. A broken flange is the main reason new toilets rock and leak. We repair or replace the flange so the bolts hold firmly before setting the new toilet.

The flange should sit on top of the finished floor. If new tile raised the floor, an extension ring or thicker seal brings it back to the right height. We check the subfloor for soft spots, especially around old toilets that leaked. Shims under the base level the toilet so it does not rock, and caulk around the base keeps cleaning water out.

Supply line and stop valve

Every install gets a new braided stainless supply line. We also check the shut-off valve behind the toilet. Old multi-turn stops often seize or drip once disturbed, and many older homes have no shut-off at all, just a bare supply pipe. Replacing it with a quarter-turn stop while the toilet is off costs little and makes future repairs easier.

After setting the toilet, we fill it, flush several times and check for leaks at the base, tank bolts and supply. We adjust the fill level so the toilet flushes well and does not overflow into the tube. The old toilet is hauled away. If you bought your own toilet, we install it as long as it fits the space.

kitchen sink with new faucet and garbage disposal installed under the counter

Around Hartford

What we see in local homes

Many Hartford-area bathrooms in older houses have non-standard rough-ins, cast-iron or lead closet bends and floors raised by layers of tile and vinyl, so measuring and checking the flange is part of every job. Narrow staircases in two- and three-family houses make two-piece toilets easier to carry up. MDC bills on metered use, so efficient toilets cut water and sewer costs. We install toilets in Hartford, Windsor, Bloomfield, Rocky Hill and other nearby towns.

What it usually costs

$285 to $865

Flange repairs, floor height, new stop valve and the toilet model you choose change the total price. Typical Hartford-area range, confirmed on site before work starts. Compare all prices.

Process

How we handle toilet installation

  1. 1

    Measure and confirm

    We measure the rough-in and space so the toilet you choose fits the bathroom.

  2. 2

    Remove the old toilet

    We shut off water, drain and pull the toilet, scrape the old seal and inspect the flange and floor.

  3. 3

    Set the new toilet

    We repair the flange if needed, set the toilet level with a new seal, bolts, supply line and stop.

  4. 4

    Flush, check and haul

    We test several flushes, check every joint, caulk the base and take the old toilet away.

FAQ

Toilet Installation questions

Most installs take one to two hours, including removing the old toilet, setting the new one and testing. If the flange or subfloor needs repair, or a new shut-off valve is needed, it can take longer. We tell you upfront if we expect extra time.

Yes. We install customer-supplied toilets as long as the rough-in and space fit. Check that the box includes the tank, bowl, seat and bolts, since some models sell parts separately. If it does not fit the rough-in or the room, we tell you before taking out the old toilet, so you are never left without one overnight.

Yes, we haul away the old toilet as part of the install. Porcelain is heavy and awkward, especially down narrow stairs in older homes, so we handle that for you. If you would like to keep it for a garden planter or any other reason, just tell us and we will set it aside.

Related work

Often booked together

Toilet Repair

The toilet runs all night, rocks when you sit, leaks at the base or barely flushes. These are small problems that waste water and rot subfloors when they are ignored.

Learn more

We do toilet installation in these areas too

Need toilet installation today?

A plumber answers, day or night, and gives you a price before any work starts.

Call (860) 926-8723
Plumber on the line 24/7 Call (860) 926-8723