Toilet Installation
The old toilet is cracked, uses too much water, or just will not stop causing trouble. A new toilet is a simple upgrade when it is set level, sealed right and...
Learn moreKitchen & bath
The toilet runs all night, rocks when you sit, leaks at the base or barely flushes. These are small problems that waste water and rot subfloors when they are ignored.

Toilet repair fixes running, leaking, weak-flushing or loose toilets by replacing flappers, fill valves, flush valves, wax rings, closet bolts or flanges. Typical Hartford-area toilet repairs run about $145 to $465, depending on what has failed. We answer 24/7, carry common toilet parts, and usually fix a toilet the same visit.
A toilet that runs or refills on its own is usually leaking water from the tank into the bowl through a worn flapper or flush valve seal. Put a few drops of food coloring in the tank and wait. If color shows in the bowl without flushing, the flapper or flush valve is the issue. A fill valve set too high can also send water into the overflow tube.
We replace flappers sized to the flush valve opening, adjust or replace fill valves, and replace the flush valve if the seat is pitted or the tube is cracked. On older toilets, finding a flapper that fits can be tricky, and a complete tank rebuild kit may be the best fix. A running toilet can waste a great deal of water over a month.
Water around the base usually comes from a failed wax ring, a cracked flange or a loose toilet that moves and breaks the seal. It can also be condensation on the tank in humid weather or a leaking tank-to-bowl gasket. We figure out which before pulling the toilet, since each needs a different repair and some need no pulling at all.
For base leaks, we pull the toilet, scrape off the old wax, inspect the flange and the subfloor, and reset with a new wax ring or foam seal and new closet bolts. Broken cast-iron or plastic flanges get a repair ring or replacement. If the subfloor is soft from long-term leaking, we tell you, because it needs fixing before the toilet is reset.
A weak flush can come from a low water level in the tank, a partly clogged trap, blocked rim jets or a venting problem. In older homes, mineral buildup under the rim and in the siphon jet slows the flush. We check the water level and flapper chain, clean the jets, and run a closet auger through the trap.
If the toilet keeps clogging, the problem may be past the toilet, in the branch drain or the main. A toilet that gurgles when another fixture drains can point to a vent problem. We look beyond the bowl so we fix the cause, and we tell you when a new toilet makes more sense than another repair.

Hartford's older houses have plenty of original or decades-old toilets, many on cast-iron flanges set into old wood floors that have shifted over the years. In two- and three-family buildings, a slow base leak in an upper unit can show up as a ceiling stain in the apartment below. MDC bills on metered water use, so a running toilet shows up on your bill. We repair toilets in Hartford, East Hartford, Newington, Rocky Hill and other nearby towns.
Which parts failed, the toilet's age and whether the flange or subfloor needs repair change the price. Typical Hartford-area range, confirmed on site before work starts. Compare all prices.
Process
We test the flush, check for tank leaks with dye and look for movement or water at the base.
We explain what failed and give you the price before we open the tank or pull the toilet.
We replace the flapper, fill valve, flush valve, wax ring, bolts or flange as needed.
We flush several times, check for leaks and leave the bathroom and floor clean.
FAQ
Most flapper, fill valve and handle repairs take less than an hour. Pulling and resetting a toilet with a new wax ring takes about an hour. Flange or subfloor repair takes longer, depending on what we find. We tell you before we start if the job is likely to take more time.
Often, yes. Many older toilets can be fixed with inexpensive parts. If the porcelain is cracked, parts are no longer available, or the toilet uses a lot of water per flush, replacing it may be the better choice. We give you both options and prices.
Sometimes a mismatched part, such as a flapper that does not fit the flush valve, causes repeat problems. Very hard water or chlorine tablets in the tank can wear seals quickly. Recurring clogs may come from the drain or vent, not the toilet. We look at the full picture.
Related work
The old toilet is cracked, uses too much water, or just will not stop causing trouble. A new toilet is a simple upgrade when it is set level, sealed right and...
Learn moreThe sink holds water, the shower drains in slow motion, or the basement floor drain bubbled up when the washer ran. Somewhere in the pipe there is a clog, and...
Learn moreYour water bill jumped, a stain keeps spreading on the ceiling, or you hear water running when nothing is on. The leak is real, but it is hiding, and guessing...
Learn moreA plumber answers, day or night, and gives you a price before any work starts.