Tankless Water Heater Installation
You want hot water that does not run out halfway through the second shower, and you want the basement floor space back. A tankless heater can do both, if the...
Learn moreWater heaters
The tankless heater is flashing an error code, the water goes hot then cold, or it simply will not fire. These units are reliable when maintained and frustrating when they are not.

Tankless water heater service covers yearly descaling, inlet filter cleaning, combustion checks and repair of ignition, flow sensor and venting faults on gas tankless units. Typical Hartford-area service visits run about $195 to $465, with part repairs priced on site. We answer 24/7, work on most major brands, and often fix no-hot-water calls the same visit.
Maintenance starts with isolating the heater using its service valves and circulating a mild descaling acid through the heat exchanger with a small pump, typically for around an hour. That removes mineral scale that reduces flow and can cause overheating. We then flush with clean water, clean the inlet water filter screen and check the condensate trap and neutralizer.
We also look at the burner and combustion air intake, check gas pressure at the unit, and inspect the vent for loose joints, blockages or damage. On condensing units, a clogged condensate line can shut the heater down. We note the unit's error history where it is stored, which often shows problems before they become breakdowns.
Ignition failures usually trace back to gas supply, a dirty flame rod or igniter, or venting issues. If the unit lights and then drops out, we check gas pressure under load, because an undersized gas line can starve the burner when other appliances run. Flow sensor faults show up as a unit that will not fire with low flow, often at a single bathroom sink.
The cold water sandwich, a burst of cold between two hot sections, happens when the unit shuts off between short draws and restarts. Small changes in minimum flow settings or a recirculation setup can help. Overheat and scale codes mean the heat exchanger needs flushing. We replace sensors, fans, igniters and boards with parts made for that exact model.
Tankless heaters generally last longer than tanks when maintained, but the heat exchanger can eventually fail, especially after years of scale or freeze damage. A leaking or cracked heat exchanger on an older unit is usually a replacement decision, since the part plus labor can cost close to a new heater, and the rest of the unit is just as old.
Freezing is a real risk for units on outside walls in a cold snap. Most have internal freeze protection that needs power. During a long power outage in winter, draining the unit can prevent damage. If you are unsure how, call and we will talk you through it or come out. We tell you honestly when a repair is worth it.

Many Hartford-area tankless heaters were installed on exterior walls in basements and utility rooms, where a January cold snap and a power outage can freeze them. Homes on MDC water see less scale than homes on wells, but every unit needs regular flushing. In Vernon, Ellington and Tolland, where wells are common, we often find scale-related shutdowns. We service tankless heaters in Hartford, West Hartford, Glastonbury, South Windsor and nearby towns.
Whether it needs only maintenance, which part has failed, and parts availability for your model change the price. Typical Hartford-area range, confirmed on site before work starts. Compare all prices.
Process
We check the error code and history and ask what the heater does, so diagnosis starts from facts.
We measure gas pressure under load, check the vent and intake, and look at the burner and flame rod.
We descale and clean the filter, or replace the failed sensor, fan, igniter or board.
We run hot water at several fixtures, clear codes and leave a note of what was done and when.
FAQ
Once a year is a good baseline for most homes. On MDC soft water, scale builds slowly, but the inlet filter, condensate trap and vent still need checking. On well water with high hardness, descaling may be needed every six months. Your unit's manual may list a schedule as well.
Often it can be reduced. The effect comes from the unit cycling off and on during short draws. A recirculation setup, a small buffer tank or adjusting minimum flow can help. Some units handle it better than others. We look at how you use hot water and suggest the simplest fix.
We service most major gas tankless brands sold in the US. Parts for common models are available quickly, while some less common or older units need parts ordered. We tell you on the phone if your model is one we can usually fix on the first visit.
Related work
You want hot water that does not run out halfway through the second shower, and you want the basement floor space back. A tankless heater can do both, if the...
Learn moreNo hot water, a shower that goes cold in two minutes, or a tank making popping noises. Most of the time a water heater can be repaired, and the trick is...
Learn moreIf you like your water but not its taste, smell or grit, a whole-house filter treats it right where it enters the home. Every faucet, shower and appliance gets...
Learn moreA plumber answers, day or night, and gives you a price before any work starts.