Shower Valve Repair
The showerhead drips all day, the water turns scalding when someone flushes, or the handle spins without changing anything. The trouble is in the valve behind the tile.
Learn moreKitchen & bath
The old tub is chipped and slow to drain, or you want a walk-in shower where a tub sits unused. What is behind the wall and under the floor decides how well the new one works.

Tub and shower installation covers removing the old tub or shower, then installing a new tub, shower pan or base with new drain, overflow and valve plumbing. Typical Hartford-area plumbing for a tub or shower runs about $1,465 to $4,285, separate from tile or surround work. We answer 24/7, and most installs take one to three days.
Many older homes have cast-iron tubs that weigh a few hundred pounds. Getting one out of a second- or third-floor bathroom usually means breaking it into pieces under a heavy tarp with a sledgehammer, rather than wrestling it whole down a narrow, turning staircase. Steel tubs are lighter but still awkward. We cover floors, banisters and stair treads before demolition starts.
With the tub out, we look at the drain and overflow. In older homes these are often lead bends or drum traps tied into cast-iron lines, and both should go. We replace them with a proper P-trap and new PVC or cast-iron fittings. We also probe the subfloor and joists, because years of small leaks around an old tub apron can rot the framing without showing from below.
Turning a tub into a shower usually means moving the drain to suit a shower base or tiled pan, raising the valve and adding a taller shower arm. A shower drain needs a two-inch trap in most cases and correct slope to the stack, and if the drain moves far, a vent connection has to move with it. We map the joists first so the new pipe runs between them instead of through them.
Shower bases come in acrylic, solid surface and composite, and go in faster than a tiled pan. A tiled shower needs a pan liner or a sheet waterproof membrane installed with care at the drain flange. We handle the plumbing side, set the drain and valve at the right depth, and coordinate with your tile installer so the finished floor and drain grate meet at the same height.
A new tub or shower is the right moment to retire an old valve. We install a pressure-balance or thermostatic valve set to the depth of the planned wall finish, using the valve's plaster guard as a gauge so the trim fits later. We also set the shower arm height for the people using it, and add outlets for a handheld or a tub spout diverter if you want them.
Before any wall gets closed, we test. The tub drain and overflow get a flood test, filling the tub to the overflow and checking below. Supply connections get pressure tested at the valve. These checks catch a weak joint while it is still easy to reach. After the tile or surround is finished, we come back to install the trim, handles, spout and drain cover.

Hartford's two- and three-family houses and older single-family homes often have heavy cast-iron tubs on upper floors, lead bends or drum traps under them, and floors that have settled over a century. Narrow stairs make tub removal a planned job, not a carry-out. Ceiling stains below a tub are one of the most common calls we get in multi-unit buildings. We install tubs and showers in Hartford, West Hartford, Newington, Bloomfield and other nearby towns.
Tub removal difficulty, drain and valve changes, conversion work and framing repairs change the plumbing price most. Typical Hartford-area range, confirmed on site before work starts. Compare all prices.
Process
We look at the old fixture, drain, valve and framing, and plan the new tub or shower plumbing.
We remove the old tub or shower, protect floors and stairs, and inspect the pipes and framing.
We set the tub or base, replace drain and overflow, install a new valve and pressure test.
After tile or surround, we install trim, test everything and clean up the bathroom.
FAQ
The plumbing part usually takes one to three days, depending on drain changes and valve work. Tile or surround work adds time, often several days, before we return for trim. We schedule the plumbing to fit with the other trades and give you a realistic idea of how long the bathroom will be out of use.
Often, yes. Old tubs frequently have narrow drain shoes, drum traps or partly clogged cast-iron lines below them. Replacing the drain and trap with properly sized pipe usually fixes slow draining for good. If the restriction is farther down the line, we clean or repair that section as part of the job.
We handle the plumbing: removing the old fixture, drains, valves, and setting the tub or base. Tile and surround work is usually done by a tile installer or general contractor. We coordinate heights and drain locations with them so the finished wall and floor line up with the fixtures.
Related work
The showerhead drips all day, the water turns scalding when someone flushes, or the handle spins without changing anything. The trouble is in the valve behind the tile.
Learn moreYou are gutting a kitchen or bathroom, and the plumbing behind the walls has to fit the new layout. This is the stage where good decisions save money and...
Learn moreOld cast-iron drain lines can split along the bottom, rust through at the hubs or start weeping sewer gas into the basement. We replace the bad sections before...
Learn moreA plumber answers, day or night, and gives you a price before any work starts.