Faucet Repair & Replacement
The kitchen faucet drips all night, the bathroom handle is stiff, or water pools in the cabinet every time you rinse a dish. A faucet gets used more than any...
Learn moreKitchen & bath
A new countertop, a cracked basin, or a laundry room that needs a utility sink. Swapping a sink looks simple until the drain height, trap arm and old stops get involved.

Sink installation covers setting a new kitchen, bathroom, laundry or bar sink and connecting the faucet, drain, trap and supply lines, with new stop valves where needed. Typical Hartford-area installs run about $245 to $685 for plumbing labor and parts, plus the sink. We answer 24/7 and usually finish in one visit after counters are set.
Kitchen sinks come as drop-in, undermount and farmhouse styles in stainless, enameled cast iron, fireclay and composite. Each needs proper support. Undermount sinks hang from clips or epoxied brackets under stone counters, and a heavy fireclay apron sink usually needs a support frame built into the cabinet. On stone counters the fabricator normally sets the sink, and we connect the plumbing after.
Double-bowl sinks need a continuous waste or baffle tee joining both drains into one trap, and a disposal on one side changes that layout. The trap arm must slope down to the wall connection, about a quarter inch per foot. In older kitchens the drain in the wall is often set high for a shallow sink, so a deep modern bowl can leave no room for the trap until we lower the drain inside the wall.
Bathroom choices include vanity tops, vessel bowls, wall-hung basins and pedestal sinks. Pedestal and wall-hung sinks rely on solid blocking in the wall, since the pedestal mostly hides pipes and does not carry the full weight. On plaster walls in older houses, that often means opening the wall to add a crosspiece. Vessel sinks sit high and need a tall faucet or a wall-mounted spout.
Pop-up and grid drains seal to the basin with a gasket or putty, and a sink with an overflow needs a drain body with an overflow slot. On pedestal and wall-hung sinks, the stops and supply lines are on display, so we use chrome stops and keep the lines straight and symmetrical. We set the trap height so the trap arm lines up cleanly with the wall drain without awkward offsets.
A basement laundry or utility sink earns its keep for washing paint brushes, filling mop buckets and taking washer discharge. It needs a trapped drain with a vent connection and both hot and cold water. In basements where the building drain runs overhead or above the sink, a small sink pump lifts the water up to the main line, and it needs its own outlet nearby.
If the washer drains into the sink, the basin and drain must handle the washer's pump rate, or water will rise over the rim during the spin cycle. We check the drain size and venting, and clip the washer hose so it cannot jump out of the basin. A utility faucet with a hose thread is useful here, and we fit one with a built-in backflow preventer.

Older Hartford-area kitchens often have wall drains set for shallow sinks, so a deeper modern bowl can need a drain change. Many bathrooms in two- and three-family houses have pedestal or wall-hung sinks on plaster walls that need added blocking. Basements often have old laundry tubs hooked up with improvised drains and no trap. We install sinks in Hartford, West Hartford, Wethersfield, Newington and other nearby towns.
Sink type, drain height changes, new stops, extra support and any pump needs change the plumbing price. Typical Hartford-area range, confirmed on site before work starts. Compare all prices.
Process
We check the sink, faucet, counter cutout and wall drain height to make sure everything lines up.
We disconnect and remove the old sink if present, and replace stops or drain parts as needed.
We set or connect the sink, install the faucet, drain, trap and supply lines.
We run water, fill and drain the sink, check for leaks and clean up the area.
FAQ
Most bathroom sink installs take one to two hours. A kitchen sink with a faucet, disposal and dishwasher connection usually takes two to four hours. A basement utility sink with new drain and water lines can take most of a day, especially if it needs a pump. We schedule kitchen sink work after countertops are in place.
Yes. For undermount sinks on stone, the countertop fabricator usually mounts the sink, and we connect the faucet, drain and supply lines afterward. For drop-in sinks, we can set the sink in the cutout and connect everything ourselves. We coordinate timing with your counter installer so the kitchen is not out of use longer than needed.
It can. We install a new faucet you provide, or reuse your existing faucet if it is in good shape and fits the new sink. Since the sink is already out, replacing an older faucet at the same time saves a separate visit later. We check the faucet against the sink's hole count before installation day.
Related work
The kitchen faucet drips all night, the bathroom handle is stiff, or water pools in the cabinet every time you rinse a dish. A faucet gets used more than any...
Learn moreThe disposal hums but will not spin, it drips onto the cabinet floor, or it went silent mid-cleanup. Some of these take ten minutes to fix, and some mean the...
Learn moreYou are gutting a kitchen or bathroom, and the plumbing behind the walls has to fit the new layout. This is the stage where good decisions save money and...
Learn moreA plumber answers, day or night, and gives you a price before any work starts.